You have no items to compare.
Features
The ElectroGen® converts one ounce of Thermo 55® into a 2,000 cubic foot deodorizing cloud - IN JUST 30 SECONDS! Specially insulated barrel produces smallest particle size. The machine comes with an instruction and maintenance manual. Insist on the Original...If it doesn't say Unsmoke®, it's not an Electro-Gen®, the industry's most durable electric thermal fogger.
Wet particles produced by conventional sprayers and ultra low vapor foggers may cause unwanted moisture problems inside wall cavities. The dry fog produced by the ElectroGen fogger consumes just 1 ounce of solvent based deodorizer per minute.
Remove the barrel and the Electro- Gen® also can be used as an electric sprayer to apply solvent or water based chemicals for deodorizing, disinfecting, flame proofing, pest control, fabric protecting, etc.
Deodorization Tips
Thermal fogging is the third step in the Prorestore® Structural Smoke Odor Removal Procedure.
Prior to thermal fogging:
Step 1
Suppress odor sources such as charred wood, or horizontal structural
surfaces, etc. by low pressure spraying with a solution of 3-4 ounces
(89ml - 118ml) ODORx 9-D-9 or ODORx Double-O per gallon of water.
A deodorizing pre-sealer for containing odors on structural surfaces such
as charred wood, attic insulation, voids above suspended ceilings etc.
can be prepared by adding the following to an empty 5 gallon container:
- 1 gallon (3.8 Liters) ODORx Unsoot #1
- 1 quart (0.95 Liters) ODORx 9-D-9
- 5 ounces (150ml) ODORx Last Resort™
- Fill the balance with water to make 5 gallons
Apply with low pressure electric sprayer or commercial airless paint
sprayer. One gallon covers approximately 500 square feet.
Step 2
Vapor phase odor control is achieved by applying 2 ounces (60ml) of
ODORx Crystal Odor Counteractant (C.O.C.™), per 100 sq. ft./9.3 square
meter (of floor area) to floors throughout the area to be treated.
Step 3 - Thermal Fogging
A. When thermally fogging it is advisable to begin treatment at the
furthest inward point of the area to be treated and work your way back
to the entry.
B. Close doors in rooms and closets after thermally fogging to contain
fog in treated areas.
C. Treat rooms and closets prior to treating open public areas.
D. When thermally fogging indoors, pause after each 15 seconds of
thermal fogging and release trigger for 30 seconds to allow barrel to
re-heat to most efficient thermal fogging temperature.
ElectroGen Thermal Fogger Maintenance
The Electrogen Thermal Fogger is extremely easy to maintain.
1. Make sure the unit has not been in use and that the barrel is cool to the touch. Remove the barrell
2. Pour any remaining solution back into its original container.
3. Rinse solution canister thoroughly. Add clean water and reattach canister to fogger. TIP - Add a small amount of dish soap to the water
4. Run fogger with barrel OFF for at least 1 minute.
5. Discard remaining liquid, dry out canister, replace and store.
Note: *Available in International Voltage for Special order.
Wet particles produced by conventional sprayers and ultra low vapor foggers may cause unwanted moisture problems inside wall cavities. The dry fog produced by the ElectroGen fogger consumes just 1 ounce of solvent based deodorizer per minute.
Remove the barrel and the Electro- Gen® also can be used as an electric sprayer to apply solvent or water based chemicals for deodorizing, disinfecting, flame proofing, pest control, fabric protecting, etc.
Deodorization Tips
Thermal fogging is the third step in the Prorestore® Structural Smoke Odor Removal Procedure.
Prior to thermal fogging:
Step 1
Suppress odor sources such as charred wood, or horizontal structural
surfaces, etc. by low pressure spraying with a solution of 3-4 ounces
(89ml - 118ml) ODORx 9-D-9 or ODORx Double-O per gallon of water.
A deodorizing pre-sealer for containing odors on structural surfaces such
as charred wood, attic insulation, voids above suspended ceilings etc.
can be prepared by adding the following to an empty 5 gallon container:
- 1 gallon (3.8 Liters) ODORx Unsoot #1
- 1 quart (0.95 Liters) ODORx 9-D-9
- 5 ounces (150ml) ODORx Last Resort™
- Fill the balance with water to make 5 gallons
Apply with low pressure electric sprayer or commercial airless paint
sprayer. One gallon covers approximately 500 square feet.
Step 2
Vapor phase odor control is achieved by applying 2 ounces (60ml) of
ODORx Crystal Odor Counteractant (C.O.C.™), per 100 sq. ft./9.3 square
meter (of floor area) to floors throughout the area to be treated.
Step 3 - Thermal Fogging
A. When thermally fogging it is advisable to begin treatment at the
furthest inward point of the area to be treated and work your way back
to the entry.
B. Close doors in rooms and closets after thermally fogging to contain
fog in treated areas.
C. Treat rooms and closets prior to treating open public areas.
D. When thermally fogging indoors, pause after each 15 seconds of
thermal fogging and release trigger for 30 seconds to allow barrel to
re-heat to most efficient thermal fogging temperature.
ElectroGen Thermal Fogger Maintenance
The Electrogen Thermal Fogger is extremely easy to maintain.
1. Make sure the unit has not been in use and that the barrel is cool to the touch. Remove the barrell
2. Pour any remaining solution back into its original container.
3. Rinse solution canister thoroughly. Add clean water and reattach canister to fogger. TIP - Add a small amount of dish soap to the water
4. Run fogger with barrel OFF for at least 1 minute.
5. Discard remaining liquid, dry out canister, replace and store.
Note: *Available in International Voltage for Special order.
Additional Information
| SKU | UP102M |
| Manufacturer | Prorestore |
| Manufacturer Link(s) |
You may also be interested in the following product(s)
|
9 D 9
$83.01
|
Last Resort
$58.45
|
Skunk Odor Control
$49.17
|
Odorcide 210
Starting at: $12.32
|
